STM32F107RCT6 Microcontrollers Datasheet

 Product Overview

The STM32F105xx and STM32F107xx connectivity line family incorporates the highperformance ARM® Cortex®-M3 32-bit RISC core operating at a 72 MHz frequency, highspeed embedded memories (Flash memory up to 256 Kbytes and SRAM 64 Kbytes), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. All devices offer two 12-bit ADCs, four general-purpose 16-bit timers plus a PWM timer, as well as standard and advanced communication interfaces: up to two I2Cs, three SPIs, two I2Ss, five USARTs, an USB OTG FS and two CANs. Ethernet is available on the STM32F107xx only.

 

This blog will introduce STM32F107RCT6 systematically from its features, pinout to its specifications, applications, also including STM32F107RCT6 datasheet and so much more.

 

STM32F107RCT6 Features

• Core: ARM® 32-bit Cortex®-M3 CPU

– 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access

– Single-cycle multiplication and hardware division

• Memories

– 64 to 256 Kbytes of Flash memory

– 64 Kbytes of general-purpose SRAM

• Clock, reset and supply management

– 2.0 to 3.6 V application supply and I/Os

– POR, PDR, and programmable voltage detector (PVD)

– 3-to-25 MHz crystal oscillator

– Internal 8 MHz factory-trimmed RC

– Internal 40 kHz RC with calibration

– 32 kHz oscillator for RTC with calibration

• Low power

– Sleep, Stop and Standby modes

– VBAT supply for RTC and backup registers

• 2 × 12-bit, 1 µs A/D converters (16 channels)

– Conversion range: 0 to 3.6 V

– Sample and hold capability

– Temperature sensor

– up to 2 MSPS in interleaved mode

• 2 × 12-bit D/A converters

• DMA: 12-channel DMA controller

– Supported peripherals: timers, ADCs, DAC, I2Ss, SPIs, I2Cs and USARTs

• Debug mode

– Serial wire debug (SWD) & JTAG interfaces

– Cortex®-M3 Embedded Trace Macrocell™

• Up to 80 fast I/O ports

– 51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant

• CRC calculation unit, 96-bit unique ID

• Up to 10 timers with pinout remap capability

– Up to four 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input

– 1 × 16-bit motor control PWM timer with dead-time generation and emergency stop

– 2 × watchdog timers (Independent and Window)

– SysTick timer: a 24-bit downcounter

– 2 × 16-bit basic timers to drive the DAC

• Up to 14 communication interfaces with pinout remap capability

– Up to 2 × I2C interfaces (SMBus/PMBus)

– Up to 5 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)

– Up to 3 SPIs (18 Mbit/s), 2 with a multiplexed I2S interface that offers audio class accuracy via advanced PLL schemes

– 2 × CAN interfaces (2.0B Active) with 512 bytes of dedicated SRAM

– USB 2.0 full-speed device/host/OTG controller with on-chip PHY that supports HNP/SRP/ID with 1.25 Kbytes of dedicated SRAM

– 10/100 Ethernet MAC with dedicated DMA and SRAM (4 Kbytes): IEEE1588 hardware support, MII/RMII available on all packages

 

STM32F107RCT6 Pinout

The following figure are the diagrams of STM32F107RCT6 pinout.

 

STM32F107RCT6 Applications

The STM32F105xx and STM32F107xx connectivity line microcontroller family are suitable for a wide range of applications such as motor drives and application control, medical and handheld equipment, industrial applications, PLCs, inverters, printers, and scanners, alarm systems, video intercom, HVAC and home audio equipment.

If you want to know more about STM32F107RCT6, you can read its datasheet.